2015 Cyber Stock Rules

Click Here For Printer Friendly Version

All drivers must have a RaceCeiver one way communication device.

General Rules & Procedures

1. The rules and/or regulations set forth herein do not express or imply warranty of safety from publication of or compliance with these rules and/or regulations; they are intended as a guide for the conduct of the sport and are in no way a guarantee against injury.

2. Hartford Speedway may at anytime make amendments to the rules set forth.

3. Hartford Speedway officials shall have full authority over events. At the discretion of Hartford Speedway officials, any competitor may be  penalized for rule violations, hazardous actions or assaults/threats against any official.

4. Cars will be permitted to race after Hartford Speedway inspector approval.

5. The uses of pit boards or colored flashlights are prohibited.

6. No radios or mirrors are allowed.

Note

1. This division will be competitive. Hartford Speedway officials reserve the right to add weight to any location, install air restrictors on the engine, or impose a handicap at any time should any single car or driver dominate.

2. All competitors should have an extra 100lbs of lead painted white, pre-drilled, with 1/2” bolts and large washers, so this lead can be readily added to your car in the event of a rules infraction.

3. All rubber boots will be removed from your struts for ease of inspection.

4. No limited slip, locked, or welded differentials.

5. No computers (Laptops, smart phones, tablets, etc) will be permitted in the car during on track competition.

Cars

1. All cars will be a 4 or 6 cylinder, front wheel drive car, with a manual or automatic transmission.

2. Convertibles, 2 seat coupes, super or turbo charged cars will NOT be permitted.

3. Cars with four wheel steering will not be permitted.

4. These vehicles will remain stock, in their original form and shape. No alterations will be made to your cars, unless it is stated that you may do so.

Safety Requirements

Driver

1. Safety rules will be strongly enforced in this class. You will be required to have a full fire suit, a minimum full face Snell SA2000 or above approved helmet (DOT Helmets will not be permitted because of the lack of fire protection), along with racing gloves, a 4 or 5 point racing harness, a good quality window net with a quick release latch, adequate roll bar padding, and an aluminum racing seat. Racing boots, a neck collar or head & neck restraint is highly recommended.

Car

1. Although we are strongly encouraging people to build and work on their own cars, if you have little or no experience putting in a safe roll cage, contact a good welder to help you install a good quality roll cage, your racing seat, and your safety belt and window net mounts.

2. All cars will have a minimum of a 4 post roll cage. The minimum round or square tubing size is 1 1/2” x .095 thickness, no exhaust tubing or old rusty well pipe allowed. The rollover bar will be behind the driver’s head, with the upper halo section constructed to give the driver plenty of head clearance & protection to provide safety in the event of a rollover. All cars will have a minimum of 3 driver’s side door bars, as well as a single or an X door bar on the passenger side. A 30” wide by 12” tall by 1/8” thick driver’s side doorplate is required on all cars (minimum size). All doors must be bolted, welded or chained shut. The back of the seat must be secured to the horizontal back bar of your roll cage. An aluminum racing seat is mandatory.

3. Front Hoops may be added for safety as well as keeping the car from bending so easy. 1 3/4” round tubing maximum (no heavy square tubing or channel). You may build your radiator support rather than using the stock core supports. Stock bumpers & all front OEM sheet metal are still required.

4. Rear bars will be a maximum of 1 3/4” round or square tubing. The rear bars may extend rearward from the top of the cage behind the driver, angling down to the rear of the trunk area. You may also have 2 bars extending back from the middle section of the back hoop, rearward. No bars may extend through the rear of your trunk area. Your may have an X in between your two rear diagonal bars. The rear strut towers may be supported with your back bars, to help keep your strut towers in place. We will be allowing bars to extend through the front firewall, for added leg protection for the driver. These bars may attach to the strut towers, but may not go any farther forward. Cars must have shut off switch next to driver window which can easily be reached from the outside of the car.

5. The front windshield opening must be covered with wire mesh. Three vertical driver protection bars are required in the windshield ahead of the driver.

Bumpers

1. We will allow you to beef up & secure your bumpers to your frame mounts, with a maximum of 1/8” thick angle iron or flat stock. You may add one piece of 1 3/4” x .090 (maximum size) tubing between your frame horns (both front & rear) to give you a solid place to attach your chain/cable hook-up. You may attach expanded sheet metal or screen in front of your radiator to protect from debris & mud.

Towing Hookups

1. All cars are required to have a cable or chain to hook up to on the front and rear of the car in the event of needing to tow your car off the track.

2. You will be allowed to add one piece of 1 3/4” x .090 (maximum size) tubing between your frame horns (both front and rear) to have a solid place to attach your chain/cable hook-up. Make sure your tubing is welded solid & that your chain or cable will life your car up safely & square with the track (not just around one side of the frame horn).

Gas Tanks & Batteries

1. If the stock gas tank is located ahead of the rear axle, it may remain in place as is (Skid plate is highly recommended!). Double check the gas lines and the tank straps, replace them if they are worn. All stock tanks located behind the rear end must be removed and relocated to the trunk area or replaced with an 8 gallon (or smaller) fuel cell and place it in the forward area of your trunk. These tanks must have a metal frame to hold the tanks in place, and must be strapped in place securely. A couple loops of plumbers strap will not suffice for this, these tanks must be secured solid. If you have a tank in the trunk area, you must patch your entire rear firewall with sheet metal, so you can’t see any of the trunk area from inside of the driver’s cockpit area. All fuel pumps are required to have a Kill Switch for the fuel pump shut off, located in plain site, in the window opening behind the driver.

2. All batteries that are mounted inside the driver’s compartment must be completely enclosed in a marine-type box with a lid, and mounted securely.

3. Remember to disconnect your battery whenever working on your fuel system!

Complete Stock Bodies

1. Doors, fenders, trunks, roof, may be skinned, but must remain stock, full, and intact. The main core of the body must remain intact between all strut towers for strength.

2. All glass must be removed 100%. All mirrors, upholstery, insulation inside & under the hood, carpet, tail lights & headlights, all loose trim on the exterior of the body, trailer hitches, and aftermarket add-ons must be removed from the car. Any material burnable in the driver’s cockpit area must be removed. The original hood & trunk latches must be removed and replaced with a quick release hood pin system. Any car with a hatchback can weld or bolt your hatchback solid. All holes in the floorboard and front firewall must be covered securely with sheet metal. Both front & rear bumpers must be strapped or chained to the frame, to prevent dragging. When you remove the vinyl covering on your dashboard, you may cover up the “ugly stuff” with a piece of aluminum or sheet metal. Make sure all loose glass or material inside of the body panels are vacuumed out completely. All loose rust flakes or trim must be removed from your cars. Use a sledgehammer on your bumpers to knock off all of the loose material on the bottom side of your car.

3. Before your car will be allowed on the track, make sure the cockpit area as well as the trunk area is clean & vacuumed out 100%!

Steering & Suspension

1. All steering and suspension will remain stock with no modifications front to rear & side to side. You will be allowed to adjust camber on all four corners. Wheelbase may be adjusted. Minimum wheel base on either side may not be less than 92”.

2. You may have a quick release steering wheel for safety, but will have the complete stock steering assembly.

3. Struts may be taken off for inspection at any time during that day’s event.

4. Heim joint suspension components will not be permitted. All suspension components must utilize stock bushings and mounts.

5. Coil overs and adjustable struts will not be permitted.

6. No made for racing shocks. One shock per wheel.

7. Spring rubbers and bump stops will be permitted.

Engines & Exhaust

1. All cars may start with the stock key or with a push button & toggle switch, hooked directly to your steering column wiring harness. All of the stock wiring to your car will remain intact.

2. Engines and transmissions are to remain stock. Honda VTEC or variable cam timing engines will not be permitted.

3. If necessary in the interest of competition Hartford Speedway reserves the right to install a 1” or 1.25” air restrictor on any car at any time.

4. Stock Engine Control Module (ECM) only for all makes and models. Stand alone Engine Control Unit’s (ECU) will not be permitted. Hartford Speedway reserves the right to inspect any ECM at any time.

5. A stock style exhaust system complete with a working muffler will be mandatory. 2” maximum OD size – catalytic converter not needed. No exhaust leaks or opening up of the mufflers allowed.

6. Absolutely no Antifreeze is allowed!

Wheels

1. Stock wheels for that make & model of car are fine. 7” wide steel safety wheels are permitted. Maximum tread width is 74”. Oversized 1” lug nuts are highly recommended. All wheel weights must be removed from both the inside & outside of all wheels.

Tires

1. Any DOT tire with a minimum wear rating of 380 will be permitted. (No “racing” tires or performance tires such as Falken Azenias or Kuhmo Supra’s.).

Weight

1. All cars will weigh a minimum of 2000 lbs race ready including the driver.

2. All lead will be painted white and will be secured with ½” bolts & flat washers.

3. All lead mounting will be subject to the tech official’s discretion.

Towing Hookups

1. All cars are required to have a cable or chain to hook up to on the front and rear of the car in the event of needing to tow your car off the track.

You may also like...